|
The Honey Bee King 2 is the top of the range helicopter from Esky and the highest spec model we sell not to mention one of the best quality electric helicopters on the market. It is the step up from the Honey Bee CP2 and is feature packed for extreme stunts and tricks. If you have had a 4ch or 6ch helicopter before and want to take the hobby to the next level then this model can go all the way. This is the King 2 which is the newest version of the King which features and improved belt drive system and many design improvements.
The main differences between a standard 6ch heli and this are:
1. Belt driven tail - Unlike the CP2 which has a separate motor on the tail this has a new belt driven tail system for precise aeriobatic actions and more reliable performance. The tail system has a slipper clutch to help avoid damage if you crash it.
2. Sturdier construction - The King 2 features a metal tail boom, strong plastic fins and bulkier parts all round.
3. Super 370 upgraded motor - This powerful large current motor gives enough torque to pull off the most demanding stunts.
4. Separate gyro etc - Most helicopters have an all in one mixer, receiver, speed controller and gyro. This is great for simple helicopters but for a stunt helicopter like this an all in one unit would not be enough. The King 2 therefore comes with separate high quality receiver/mixer, speed controller and Gyro making it highly adjustable and reliable.
5. Upgradeable - The King 2 features upgradeable parts which are available from our upgrade section. The model can be kitted out with metal parts and you can even swap the standard cabin for a highly detailed scale cabin for ultimate realism.
| 6. New 6 channel Transmitter with PIT and PLT mode lock switch and adjustable dial. |
|
|
|
The Honey Bee King 2 also has all the great features of the standard CP2 such as CCPM collective pitch which changes the actual angle of the blades to give more lift, wooden blades and a lithium battery for greater power and flight times.
|
Click here to download a video of the helicopter in action!
|
Specs:
Tail boom mounted rudder servo and durable landing struts
Each model is individually inspected at factory
Ball bearing tail blade grips with tail gear drivesystem
Weight: 470g
Length: 535mm
Main blade construction: Wood
Power system:370 motor
Control mode: CCPM SYSTEM
Transmitter: 6 CH with CCPM system
Servo: 8g,1.3kg/CM,0.13s/60
Battery: 11.1v 1000mAh Li-polymer
Radio Control Range: 2500 feet (762m)
Frequency: 35Mhz with changeable crystals
Flight time: About 20 minutes
Required to fly: 8 Normal AA batteries
|
Features:
Improved blades give superior lift. Their pop off design gives extra protection in case of heavy landing
CCPM mixing control system and collective pitch structure make perfect 3D maneuvers such as roll, inverted, and swoop flights
120 degree CCPM system provides precise movement if comparing with the traditional mechanical mixing since there are less linkage/push-rod in the helicopter and weight is greatly reduced
Bell-heller mixing greatly increase the sensitivity
O-ring inside the center hub reduce oscillation of main blades
Powerful 370 motor makes flight much more stable
The autorotation landing system with quality one-way bearing helps protectsyour helicopter from damage
Hard, Light weight Main Blades
Improved battery support that holds the battery firmly, and can be adjusted to suit your balance of flying
Tail rotor driven by belt transmission provides stable flight and low noise
Servo Controlled Rudder
High quality Gyro
Separate main shaft and main gear reduce repair time and noise
Weight is a key to a EP helicopter, lightened skid set, main gear, main frame and canopy reduce the load
Very tough rotor head
PCM receiving and transmitting system increases the operation stability
Excellent performance outdoor and indoor
Tail blade adopt flameout landing system
Metal ball swashplate for improved stability and sensitivity
Pre position servo mounts
Digital Proportional Motor Speed Control
Full parts backup
Complete Kit, Ready to Fly
|
|
.gif)
(1).jpg)
(3).jpg)
 copy(1).jpg)
.jpg)
.gif)
.jpg)
.jpg)
.jpg)
.jpg)
.gif){kind=small}
